Fastest: call (833) 490-5225. Or send this and we call you back.
Water extraction
Emergency water extraction: what it covers
Quick answer
Emergency water extraction is the removal of standing and pooled water from a floor, a basement or a crawl space with pumps and vacuums. In Independence the call line is answered 24/7 and a crew is dispatched as fast as one is available. Extraction comes first because drying cannot start while water is still sitting there.
A sudden leak does not stay where it starts. A supply line that lets go behind a washer, a water heater that splits at the seam, or a fitting that fails under a sink can put water across a kitchen floor in minutes and down through the ceiling below soon after. Extraction is the first job on a wet property because everything that follows depends on it: the water has to leave before the structure can dry.
The work is mechanical and fairly simple to describe. A technician arrives with pumps and wet vacuums sized to the volume of water, pulls the pooled water off the surface, and then goes after what has already soaked into carpet, padding, baseboards and the bottom of the walls. The aim is to take out as much liquid as possible by machine, because machines remove water far faster than air movement ever will.
Independence Water Damage Restoration answers water emergency calls for Independence and the rest of Jackson around the clock, and a crew is dispatched as fast as one is available. No arrival time is promised on the phone, since traffic, weather and the number of calls in the metro all change it. What you can do while you wait is covered below, along with how extraction fits into the drying that follows.
Do not step into standing water if any outlet, cord, appliance or the electrical panel is wet or under it, because the water can carry current. Do not use a household vacuum on water, and do not run a ceiling light or fan under a dripping ceiling. Do not lift a sagging ceiling or open a wall to look inside while it is wet. Water that came from outside the plumbing may carry contamination, so avoid contact and wash well afterward.
Water pooled on a floor or ankle-deep in a lower level
A ceiling that sags, stains or drips below a bathroom or kitchen
Carpet that squishes underfoot or feels cold and heavy
The sound of running water when every fixture is off
A musty smell that appears within a day of a leak
Baseboards or paint that bubble, lift or swell at the bottom
Water coming up through a floor drain or around a sump
A water meter that keeps turning with the whole house shut off
Our process
How our emergency water extraction visit works
Stop the source and make the room safe
The first call usually includes finding the shutoff valve for the line or fixture that is leaking. A technician will also ask where the breaker panel is and whether any outlets or appliances stand in the water. Safety comes before pumping, because water and live electricity in the same room is the one hazard that cannot be managed by working carefully.
Survey where the water went
Pooled water is only the visible part. The technician checks adjoining rooms, the floor below and the base of the walls with a moisture meter, so the extraction plan covers every wet area and not just the one with the puddle. Water that has travelled under flooring or into a wall cavity is mapped before any machine is set up.
Pump or vacuum the standing water
Deeper water is moved with a submersible pump through a hose to a drain or the outdoors. Shallow water and what remains after the pump are lifted with truck-mounted or portable extractors. The technician works in passes across the floor, since a pool that looks gone often leaves a film that keeps feeding moisture into the materials beneath it.
Extract from carpet, padding and hard surfaces
Carpet and padding hold a surprising volume of water. A weighted extraction tool presses it out of the pile, and the padding is often lifted or removed because it dries slowly and traps moisture against the subfloor. On tile, vinyl or wood the technician lifts water from seams and edges, where it collects and creeps under the finish.
Hand over to drying and document the loss
Once the water is out, the room is metered again and the drying plan is set: air movers, dehumidifiers and, where needed, opened wall bases. Photos and moisture readings are recorded as the job progresses, which helps if an insurance claim follows. Extraction ends here, and structural drying begins.
How quickly does water need to come out of a house?
As quickly as it can safely be done. Water that sits keeps spreading into materials, and wet building materials begin to support mold growth within a few days. Extraction in the first hours limits how much of the structure ever becomes saturated.
University of Missouri Extension guidance on flooded homes says mold grows on materials that stay damp for more than two to three days. That is the clock behind the urgency. Extraction does not finish the job by itself, but it starts the drying that has to happen inside that window, and it removes the largest single source of moisture in the building.
There is also a practical side. Water that stays on a floor wicks up into drywall and baseboards, soaks the padding under carpet, and finds its way down through any gap in the subfloor. Each of those is a larger repair than a puddle was. The sooner a technician starts pulling water, the smaller the area that has to be opened up later.
What can I do before a crew gets there?
Stop the water at its source if you can reach the valve safely, keep out of rooms where water meets electricity, and lift small items off wet floors. Leave the heavy work to the equipment.
Turn off the shutoff for the leaking fixture, or the main valve where the water enters the house, if that valve is dry and easy to reach. Move rugs, shoes, boxes and furniture legs off the wet floor, and put foil or plastic under furniture feet that cannot be moved. Photographs of the water and the damage are worth taking before anything is shifted.
What to avoid matters just as much. Do not use a household vacuum on water, do not run a ceiling fixture that is dripping, and do not walk through a flooded room where outlets or a panel are low. If the power cannot be shut off from a dry spot, stay out and tell the dispatcher so the crew arrives prepared.
What changes the price of extraction?
Volume of water, how far it has spread, what it has soaked into and how hard the space is to reach all move the price. It is explained and approved before any work starts.
A cup of water and a flooded basement are both called extraction, but they are not the same job. The amount of water decides the equipment and the hours. The kind of flooring matters, since carpet and padding take more work than tile. Access matters too: a low crawl space or a finished lower level with a narrow stair is slower than an open floor.
The cause also shapes the work. Clean supply water from a failed line is handled one way, and water that came in with a storm or up from a drain is handled another. Because those variables are only visible on site, the technician looks first, explains what the job involves, and gets your approval before any work begins. Nothing is done on a guess.
Is water extraction the same as drying the house?
No. Extraction removes liquid water. Drying removes the moisture held inside materials, which needs air movers and dehumidifiers and takes days rather than hours.
Pumps and vacuums can take water off a surface and out of carpet, but they cannot pull it out of framing, subfloor or the back of drywall. That moisture leaves slowly, as air moves across the material and a dehumidifier removes it from the air. The Missouri Department of Health and Senior Services estimates three days to a week for a flooded building to dry.
For that reason extraction is treated as the first stage of a longer job. Our page on drying and dehumidification explains the second stage, including how readings tell a technician when a material is actually dry rather than just dry to the touch.
Why does water from upstairs end up in the room below?
Water runs down through gaps in the floor, around pipes and along joists until it finds a ceiling. The visible stain is where it came through, not where it began.
A floor is not a sealed surface. It has openings around plumbing, vents and wiring, and seams at every joint. Water that spreads across an upstairs bathroom floor will find those openings and drip into the ceiling cavity below, where insulation and drywall soak it up and hold it.
This is why a technician checks the level below any wet room, even when the ceiling looks fine. A wet ceiling cavity can sit unnoticed for days. Opening a small inspection point or reading the surface with a meter shows whether extraction needs to reach it. The page on ceiling water damage covers that case in more detail.
Options
Types and options for emergency water extraction
A small leak from one fixture
A supply line, an ice maker or a toilet connection can wet one room without flooding it. Extraction here may be little more than a wet vacuum pass and lifting a rug or a section of padding. Even a small leak deserves meter readings afterward, because water under a vanity or behind a baseboard stays out of sight and out of reach of a mop.
A failed water heater, a burst line or an overflowing tub can cover an entire level and run to the floor below. This is a pump-and-extractor job, and it usually involves removing padding and checking the ceiling underneath. The wider the spread, the more the readings matter, since moisture travels along joists and under walls.
Lower levels collect water that came from outside as well as from the plumbing. A submersible pump handles the depth, and the technician then works on walls, stored items and any finished flooring. Water from a storm or a backed-up drain is handled differently from clean supply water, which is covered on the pages for basement water removal and sewer backup cleanup.
Jackson
Why emergency water extraction is different in Missouri
Independence is a city of about 123,011 people at the 2020 census, and it covers a lot of ground, from the older bungalow streets of Mount Washington and Fairmount in the northwest to the neighborhoods that run east toward the Little Blue River valley. Older houses with basements and crawl spaces are common in that mix, and a lower level is often where an interior leak ends up pooling.
Missouri weather shapes the calls that come in. Hard freezes in winter split lines that then leak at the thaw, and spring and summer storms bring flash flooding that pushes water into low rooms. Both of those cases, burst pipes and storm flooding, start with the same step: get the water out before anything else.
Calls are answered at all hours. Describe the water level and the source on the phone, since it helps the technician bring the right pump and hose for the job, and tell the dispatcher about any power concern so the crew arrives prepared.
One call and it gets handled.
A crew is dispatched as fast as one is available, and you approve the estimate before any work starts.
Removing visible water is half the job. Drying the walls, floors and framing with air movers, dehumidifiers and readings is the half that prevents mold and rot.
A homeowner policy often responds to sudden, accidental water such as a burst pipe or a failed hose, and often does not respond to slow leaks, seepage or flood.
Read the guide
FAQ
Emergency water extraction FAQs
Do I need extraction if the water is only an inch deep?
Yes, in most cases. Even a shallow film is enough to soak carpet, padding and the base of the walls, and it keeps feeding moisture into those materials. The technician will use a wet vacuum or an extractor and then check the surrounding materials with a moisture meter. A thin layer of water is the easiest kind to remove and the most expensive kind to ignore.
Will carpet have to be thrown out?
Not always. Carpet that got wet from clean supply water and was extracted quickly can sometimes be saved, while the padding underneath is more often removed because it holds water and dries slowly. Carpet exposed to storm water or sewage is a different case and is generally removed. The technician checks the source of the water and the condition of the carpet before recommending either.
How is the water removed from a basement with no drain?
A submersible pump moves the water through a hose to the outdoors or to a drain that can take it. The technician chooses where it goes. As the level drops, the pump is moved lower or swapped for a vacuum, and the last film is lifted by hand. Walls and any stored items are then checked for moisture.
Can extraction be done at night?
The call line answers around the clock, and a crew is dispatched as fast as one is available. Extraction is done whenever the water is present, since waiting for daylight lets it spread. No arrival time is promised on the call, because conditions across the metro vary. The dispatcher will tell you what to do for safety in the meantime.
What happens to the water I cannot see?
A technician reads the floor, walls and ceiling with a moisture meter and sometimes a thermal camera to find water that is inside materials. Hidden moisture is then handled in the drying stage, with air movers and dehumidifiers, and with opened wall bases if the readings call for it. Finding it early is the point of the survey.
Do I need to be home during extraction?
Someone should be present at the start so the technician can be shown the shutoff, the panel and the affected rooms. After that, the work can proceed with you nearby rather than in the room. If you cannot be there, arrange for an adult you trust to let the crew in and to approve the work, since nothing starts without agreement.
Should I call my insurance company first or get the water out first?
Get the water out first, because delay makes the damage larger, and take photographs before and during the work. Then contact your insurer with the record in hand. If a claim goes badly, complaints about an insurer in Missouri go to the Missouri Department of Commerce and Insurance. The guide on insurance claims in Missouri explains the sequence.