Make the house electrically safe first, then get the water out, dry the structure, remove wet materials to a height above the waterline, clean surfaces and only then rebuild. University of Missouri Extension guidance puts that order on its flood guide, MP904.
Key takeaways
- Electrical hazards come first, and MU Extension's flood guide MP904 says electrical equipment that was under water may fail later and breakers that were under water should be replaced.
- Floodwater carries runoff and sometimes sewage, so every step that follows treats what the water touched as contaminated until it has been cleaned and dried.
- The Missouri Department of Health and Senior Services estimates three days to a week to dry a flooded building, so drying is a planned stage and not something that happens while you work on other things.
- Wall materials are removed to a height above the waterline, because drywall and insulation wick water upward and keep it inside a closed wall.
- Hands are washed with soap and warm water after cleanup, and anyone who becomes ill during cleanup should seek medical attention.
- New coverings go in only after the building has dried fully, since mold grows on materials that stay damp for more than two to three days.
What comes first when you go back into a flooded house?
Electrical safety comes first. Do not enter standing water with power on, and do not operate switches or appliances that got wet. MU Extension's flood guide says electrical equipment that was under water may fail later.
Water and electricity do not mix, and a flooded house can hold both. Before anyone steps into standing water, the power to that part of the house should be off, and where the panel or the meter is in a wet area, that decision belongs to a qualified electrician or the utility and not to a homeowner wading in. Look first from a dry spot. If outlets, a panel, a furnace or a water heater controls sit in the water, treat the whole area as live until someone qualified says otherwise.
The hazard also outlasts the water. MU Extension's flood guide, MP904, Resources for Your Flooded Home, says electrical equipment that was under water may fail later, and that circuit breakers that were under water should be replaced. A device that works on the day of the cleanup can still be damaged inside. Do not assume that because a switch clicked and a light came on, the circuit is sound. Gas appliances that were flooded need the same cautious handling by a qualified person before use.
How should you protect yourself during cleanup?
Treat floodwater and anything it touched as contaminated. Wear gloves and sturdy waterproof footwear, avoid contact with skin and eyes, and wash hands with soap and warm water afterwards. Seek medical attention if you become ill during cleanup.
Floodwater is not clean water. It carries runoff from yards, streets and storm drains, and in places it can mix with what comes out of sewer lines. Because nobody can tell by looking what is in it, the safe habit is to assume that it is contaminated and to protect yourself accordingly. Wear rubber gloves, boots that protect the whole foot, and clothing you can wash separately. Keep children and pets out of the work area, and do not eat or drink while handling wet materials.
MU Extension's guidance is to wash hands with soap and warm water after cleanup and to seek medical attention if you become ill during cleanup. Open windows and doors where it is safe to do so, and keep your pace steady, because cleanup is heavy, wet work and tired people make mistakes. Take photographs before you move anything. For a house where sewage may have been involved, read the sewer backup guide before you start, and think carefully before doing the work without help.
How do you get the water out?
Remove standing water in stages once the power question is settled. Pumps and wet vacuums take out the bulk, and the aim is to lower the level steadily rather than all at once, so that walls and foundations are not stressed.
Once the house is safe to enter, the first physical job is to remove standing water. A pump handles depth, and a wet vacuum handles what a pump leaves behind. In a basement, taking the level down gradually is a better approach than draining everything quickly, because wet soil outside can press on the walls and a sudden drop inside can leave them unsupported. A crew that works a lower level typically lowers it in measured steps and watches the walls as it goes.
Water that cannot be pumped, such as moisture sitting in carpet, cushion and the base of the walls, comes out next through extraction. The longer it stays, the further it spreads into porous materials. Our flood water cleanup page and the basement water removal page describe how crews handle the work, and the guide on a flooded basement in the Little Blue Valley describes the situation on the east side, where the river valley sets the flood pattern.
What should be removed, and what can be saved?
Remove soaked porous materials such as carpet, cushion, insulation and wet drywall. Hard sealed items can often be cleaned and dried. Wall materials come out to a height above the waterline according to MU Extension flood guidance.
After the water, the next question is what to keep. Porous items that soaked up floodwater are the ones that are hardest to clean and the most likely to cause trouble later: wall-to-wall carpet and its cushion, insulation, mattresses, upholstered furniture and particleboard. Gypsum drywall wicks water upward, so the damage can reach higher than the visible line. MU Extension flood guidance says to remove wall materials to a height above the waterline, and that gives the framing a chance to dry from both sides.
Solid, sealed or hard-surfaced items, such as metal, glass, solid wood and some plastics, can often be cleaned and dried in place, though that depends on what water touched them. Bag and carry out what must go, and keep a list and photographs for the insurance file. For local advice on disposing of flood debris and on decontaminating what you keep, MU Extension offices can advise. The flooded flooring and drywall removal page describes the demolition itself.
How is the structure dried?
Air movers and dehumidifiers pull moisture out of the structure while readings track progress. The Missouri Department of Health and Senior Services estimates three days to a week to dry a flooded building.
Drying is a stage of its own and it takes planning. After removal, the remaining framing, the subfloor and the slab still hold water, and that water leaves only if air moves across the surfaces and the moisture it picks up is taken out of the room. Fans alone push damp air around. Dehumidifiers, and ventilation where the outdoor air is drier than the indoor air, remove the water so it does not settle on the next cool surface. Closed doors and shut windows slow things down.
The state health department's estimate of three days to a week to dry a flooded building is a guide, and each house runs to its own schedule. A moisture meter, not a hand on a wall, tells whether the framing and subfloor have reached a dry reading. Crews return, take readings in the same spots and adjust the equipment until the numbers agree. The drying and dehumidification page describes the process, and it matters because the next stage depends on a confirmed result.
When do you clean and treat surfaces?
Clean after wet materials are out and while surfaces are still open. Hard surfaces are scrubbed with detergent and water, then rinsed, and kept ventilated while they dry. Anything that remains contaminated needs more than a wipe.
Cleaning follows removal, not the other way round. Scrubbing a wall that is about to be cut out only wastes time, and cleaning over a surface that is still wet leaves moisture behind. Once the soaked material is gone and the framing is exposed, the remaining hard surfaces such as studs, concrete and tile can be scrubbed with detergent and water and rinsed, then allowed to dry. The dried surfaces can be inspected, and anything that looks stained or smells off can be dealt with before closing in.
If dark growth has appeared on the framing or on materials left too long, that is a mold question and not a simple cleaning one. University of Missouri Extension says mold grows on materials that stay damp for more than two to three days, and by then the work has moved from cleanup to remediation. The mold after a flood timeline guide covers why the window matters, and the mold remediation page covers what the job involves.
When is it safe to rebuild?
Rebuild only after the building has dried fully, confirmed by readings. Flood-damaged homes must dry fully before new coverings go in, because new flooring or drywall over damp framing traps the moisture.
The last step is the one people most want to do first. New drywall, flooring and paint make a house feel like itself again, and the pressure to get there is real. The guidance is plain though: flood-damaged homes must dry fully before new coverings go in. A new surface laid over a damp cavity hides the evidence and holds the moisture against wood, which is exactly the condition that supports growth.
Before closing anything in, confirm that the readings are dry, that electrical equipment that was under water has been checked or replaced as MP904 advises, and that the insurer has seen what it needs to see. Keep the moisture readings, the photographs and the receipts together. Closing a wall is a decision that cannot be easily undone, and a few more days of drying and checking is the safer route. The crew line at (833) 490-5225 is answered around the clock if you want a second look before you close up.
Frequently asked questions
What is the very first thing to do after a flood in the house?
Make the house electrically safe. Do not walk into standing water while the power is on, and do not use switches, outlets or appliances that got wet. Have a qualified person deal with the panel if it is in a wet area. MU Extension's flood guide says equipment that was under water may fail later, so a working light does not prove a circuit is sound.
How long should I wait before rebuilding?
Wait until the building has dried fully, confirmed by moisture readings. The Missouri Department of Health and Senior Services estimates three days to a week to dry a flooded building, though thick materials and closed cavities can take longer. Flood-damaged homes must dry fully before new coverings go in, so a premature start usually means doing the work twice.
Why remove drywall that looks fine above the water line?
Drywall and insulation wick water upward, so the wet zone is usually taller than the visible stain. MU Extension guidance says to remove wall materials to a height above the waterline. Cutting back to a clean line also lets you see the framing and dry it from both sides before anything is closed in again.
Can I clean up a flood myself?
Some of it, with care. Electrical hazards, deep water, sewage and heavy removal are the parts where help matters most. Wear gloves and boots, wash your hands with soap and warm water afterwards, and seek medical attention if you become ill during cleanup. Photograph everything first and ask your local extension office about disposal and decontamination.
What happens to circuit breakers that were under water?
MU Extension's flood guide, MP904, says circuit breakers that were under water should be replaced, and that electrical equipment that was under water may fail later. That work belongs to a qualified electrician. Do not reset or test a wet panel yourself, and do not rely on a breaker that has been submerged simply because it still switches.
Which Independence waterways flood homes?
The City of Independence names the Little Blue River valley as the main flood source for east Independence, along with Rock Creek, Spring Branch and Adair Creek. In August 2017 many Blue and Little Blue River gauges set peak records, and in July 2025 record rain fell across the metro. Water from any of them calls for the same safe order.
Sources
This guide is general information for Jackson homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.